You are currently viewing Tire Rotation on Jeep Wrangler 4 Wheel or 5 Wheel | How to rotate tires on your Jeep

Tire Rotation on Jeep Wrangler 4 Wheel or 5 Wheel | How to rotate tires on your Jeep

Most jeep owners tend to ignore vital safety checks of tire rotation on jeep wranglers and this proves to be very unfortunate for them in the long run. Drivers do not pay much attention to their tires, which is why Matt Edmonds, the executive vice president of sales at the Tire Rack, advises them to regularly rotate their tires.

Tires contribute immensely to the comfortability of the driver and vehicle control. No matter what kind of a model you have it is very much important to know the proper way for rotating tires on a jeep wrangler, with good tires, you are assured of a smooth drive, whether off or on the road. 

On the Jeep Wrangler, you rely on them more than any other outward feature of the vehicle. With good tires and the unbeatable functionality of the Jeep Wrangler, you set your limits on the roads. 

Since today’s tires are so easy to use, many people ignore the proper maintenance and inspection procedures. This will eventually lead to tire wear-out and expensive repairs. 

Why is it important to rotate tires?

Failure to rotate your tires will drive you to buy more tires in the long run. Tires like most car parts are expensive. This disadvantage can easily be dealt with if you rotate your Jeep Wrangler’s tires at the recommended intervals. 

Also, for a Front-wheel drive vehicle, if you do not check and rotate your tires regularly, the tires wear out unevenly and the front tires end up having less tread than rear ones. This then leads to unbalanced wear out of tires.

Therefore, you will end up replacing your tires after a few thousand miles. Without rotating tires, treads are more likely to be not in order, as the continuous spin of a tire in the same position for a thousand miles exposes the tire to the monotony of position. 

On an All-Wheel Drive (AWD), the tires might serve for a long while, but it is even better if the tires are rotated. Meanwhile, on a Front-wheel drive (FWD), the front tires will tend to wear out faster as compared to the rear tires. 

This happens because Front-wheel drive (FWD) equipped vehicles are essentially driven by the use of front tires, they pick the direction and direct the whole vehicle. On the other hand, in All wheel drive vehicles (AWD), power transmission is supplied to all the tires at the same time. 

Effectiveness of tire rotation on Jeep wrangler

proper way for rotating tires on a jeep wrangler

Tire rotation is usually effective when carried out between five thousand miles to eight thousand miles, or once every six months or between three oil changes, whichever comes first according to the usage of your Jeep wrangler. 

Generally, rotating tires involves changing the current tire position to another one. To people who do not usually do this, it may seem silly, but to some it is obvious. Then there are those people who never think about their Jeeps when they buy one. 

They just think about them when they get on the road. Even though a car doesn’t have suspension or alignment issues, it can still cause unusual wear patterns on its tires. Tread cupping, an issue that arises from not rotating your tires and causes high noise levels and vibration can be eliminated through regular rotating of tires. 

The use of the spare tire in rotation. 

Most spare tires are for emergency purposes, right? The Jeep Wrangler’s spare tire is more often than not, thought of in the same manner. This is wrong as it is supposed to be actively used in the tire rotation after the four tires have gone for a few thousand miles. 

It adds to the aesthetic look of the Jeep Wrangler, while attached to the back of the vehicle, but it is just waiting for its time to be rotated in and be included in the movement of the vehicle. 

It is advised to use the spare wheel in rotation of the tires as it increases longevity and lifespan of the tires by up to twenty percent, it allows one to go for a long time without having to think of buying new tires for his/her Jeep making it pocket friendly. 

It also enables even wearing out of the five tire treads. Rotating five tires as opposed to four also spreads the mileage of the Jeep evenly among the five tires. Some people however will opt to rotate four tires and exclude the spare wheel, this might happen when one is using directional tires. 

What is directional tires? 

Directional tires are the ones that have a tread pattern that is designed to direct the water away from the tires and onto the rims. They are marked with a compass on the sidewall to aid in proper alignment. 

If the arrow pointing forward is on the passenger side rim, then the directional tires will spin clockwise. If the arrow pointing backward is on the driver’s side rim, then the directional tires will spin counterclockwise. 

Due to this specialization, a spare tire cannot be used during the rotation process, and the four tires must remain on the side originally mounted to be in line with the directional compass on the side, hence the rotation using directional tires is simply from the front to back and back to front tires. 

What is the Correct tire rotation for Jeep Wrangler?

proper way for rotating tires on a jeep wrangler

How are we supposed to rotate the tires of the Jeep Wrangler in the case that we do not want to use the spare one? To rotate the four tires in your Jeep wrangler, firstly, make sure that they are all in a good condition. 

Also, be sure to follow all safety precautions while changing the tires of your Jeep Wrangler. These precautions include keeping the wheels stable and free from moving by using wheel chocks. 

Place the jack behind the tire (make sure it’s on a flat surface). Pump up the jack a little bit such that it supports the car but does not lift it. Using a lug wrench, loosen the nuts by turning them counterclockwise. 

In case a nut is stuck, you can easily use your body to turn the wrench, for example, by making little jumps with your foot to make the nuts loose. Once the nuts are loose, you can now jack up the car off the ground. Jack up the car until you can comfortably pull off the tire and insert the spare one. 

four tire rotation pattern for Jeep Wrangler

The four tires of the Jeep Wrangler are pretty easy to rotate. However, rotating the four tires differ with whether the Jeep is a Front Wheel Drive (FWD) or an All-wheel drive (AWD). After jacking up the car, you are to remove all the tires and place them against the side of the Jeep, this eases the rotation as you already know the basics. 

For a Jeep Wrangler equipped with the Front-wheel drive (FWD) system, you will pull out the driver rear tire and swap it with the passenger front tire. The passenger rear tire then is pulled off and swapped with the driver’s front tire. 

On doing that, you have successfully dealt with the rear tires, after the swap and confirming that the nuts are tightly fixed, proceed to replace the rear tires. The driver’s front tire is supposed to be put in the driver’s rear position. 

Lastly, for this front-wheel drive (FWD) Jeep Wrangler, the passenger front tire is replaced in the passenger rear position. After confirming that all the nuts are tightened, you can slowly lower the car jack. 

With this, you have successfully rotated the wheels of your front drive Jeep (FWD) Wrangler. You can now set off and the next time you will revisit this process is after about five thousand miles. 

For a jeep equipped with an All-Wheel Drive (AWD) system, the X- pattern swap is used. This mode of tire rotation involves direct swapping of tires. 

After the basic jacking of a car, and pulling out all the tires, swap the driver front tire with the passenger rear tire. Proceed to swap the passenger front tire with the driver rear tires. This way, you will have correctly rotated your four tires on your All Wheel Drive Jeep Wrangler. 

Five tire rotation pattern for Jeep Wrangler 

proper way for rotating tires on a jeep wrangler

If you plan to mix the spare tire into the rotation, which is highly recommended by experts, this is how you are supposed to go about it, For a Jeep Wrangler equipped with the All-wheel Drive (AWD) system, the process begins with the removal of the spare tire, then remove all the tires of your Jeep and place them aside. 

The spare tire is then fixed at the rear passenger’s position. The tire that was initially in that passenger rear position is put at the passenger position in the Jeep Wrangler. 

The tire that was originally at the passenger front is taken to the driver’s rear position(no.3). Then the tire that was initially at the driver’s rear position is taken to the driver’s front position(no.4). 

Finally for this Jeep Wrangler’s tire rotation, the tire that was at the driver front position, is put at the spare position. That is how the five-tire rotation of the Jeep Wrangler’s tires is done. 

Why should you pay while you can do it yourself? 

Tire rotation can easily be done in the comfort of your home. You have to assemble all the required tools before starting the process.

3 Must Tools to have before rotating tires on Jeep wrangler

Below listed are 3 major things which you must have to rotate tires by yourself. This equipment comes in very handy in times of need. Apart from the Jak Stand, Floor Jack, and Impact Wrench you also need hand gloves to protect your hands and Wheel Chocks as a safety measure to keep your jeep from rolling till lifted.

You will need some muscle power, too, and remember (for your safety) never get under a vehicle supported only by a jack!  If you are going to do it at home or pay for the rotation to be done, these instructions must be followed: 

  • Thoroughly examine the tires for any tread or sidewall damage. Remember to check both the inner walls and outer walls. 
  • Use a lug wrench when tightening the nuts. This ensures that the wheels are properly mounted to the vehicle after the rotation process. 
  • Do not be too gentle while tightening as too little tightening means that the lug nuts can separate themselves from the tire while driving. Do not tighten the lug nuts with too much force, as this means that if you get a flat you might not be able to pull out the tire to replace it with a spare. 
  • Too much tightening also risks brake rotor warping leading to vibrations while stopping and longer stopping distances. Typical tightening specifications call for about 75-100 pound-feet of torque, though some vehicles call for more. 
  • Air pressure is important when performing a tire rotation. It can be adjusted to perform a proper grip or to keep the tire pressure in the proper range. 
  • Since tires deteriorate over time, it is often recommended not to use them past the age of six years. Others place a time limit of 10 years. There is usually a DOT (department of transportation) code that can be used to determine the age of the tire.
  • To establish the age of a tire, check the last four digits of the DOT code, if it is 2619 that means the tire was made during the 26th week of 2019. 


Regular tire rotation on your Jeep Wrangler will prevent uneven wear of treads, spread out milage on the five tires and save your money as with proper rotation, one can go for a very long time before replacing the tires with a new set. Rotate your Jeep’s tires! While at it, do it correctly as elaborated above.